Loading... Please wait...


Atlas 412 Combo 12,000 LB. Cap. 4-Post Lift & 2 x Atlas RJ-6000 Rolling Jacks (Manually Operated)

Hover over image to zoom

  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5
  • Image 6
  • Image 7
  • Image 8
  • Image 9
  • Image 10
RRP: $6,999.00
$6,535.00 (You save $464.00)
Combo ATPK-412-MTG/ 2 x RJ-6000-MTG
Free Shipping
Commercial delivery with Fork Lift:
Residential delivery with Fork Lift (Add $40):

 Product Description


Atlas 412  Combo 12,000 LB.  Cap. 4 Post Lift & 2x Atlas RJ-6000 Rolling Jacks

(Manually Operated)



  • Atlas 412 12,000 LB. 4 Post Lift
  • (2) Atlas RJ-6000 Rolling Jacks (Manually Operated)








  • Description


    The Atlas 412 12,000 pound capacity four post lifts are designed and built to commercial grade standards and will provide many years of service. Our Atlas lifts offer many exclusive features not found on many other competitor's lifts. 

    Drive-through off-ramps are available as an option. 

    The Atlas 412 (12,000 LB. capacity four post lift) incorporates many structural and cosmetic features that are found on lifts costing thousands of dollars more money. The Atlas 412 is tested to ensure that this lift system will perform flawlessly at its rated capacities. The Atlas 412 has been manufactured to the same exacting specifications for many years. 

    The Atlas 412 uses a high strength cable system (with a under runway oversized hydraulic cylinder) powered by a 220 volt (single phase) power unit to raise and lower the lift. Many competitors use an "old style" chain lifting system with an exposed hydraulic cylinder system. Old style chain lifts are difficult to "level" properly and the exposed hydraulic cylinder is responsible for numerous "door dings". 


 Atlas RJ-6000 Rolling Jack
  • Manual/Hydraulic Operated
  • 6,000 LB. capacity
  • RJ-6000 rolling jack color may vary: blue or black
  • Heavy duty/commercial grade
  • Scissor mechanism allows for level
  • Compact size with a low profile
  • Adapters included
  • Safety lock positions
  • Smooth rolling action
  • Powder coated finish
  • Shipping Weight: 350 lbs.
The Atlas RJ-6000 (Manual) is a heavy duty rolling jack designed to lift and support 6,000 LB. The commercial grade RJ-6000 (Manual) rolling jack can be used to raise the front or rear portion of a vehicle; allowing the operator of a four post above ground lift to perform wheel and brake service. Most commercial shops buy two of these hydraulic rolling jacks, so that the entire vehicle can be supported in the air at the same time.

The Atlas RJ-6000 (Manual) has telescoping arms that can be extended over the runways of the four post lift. The lift pads at the end of these arms can be positioned under the LIFTING POINTS that are located over the runways of the four post lift. The Atlas RJ-6000 (Manual) rolling bridge is equipped with expandable supports which adjust to fit many different brands of four post above ground lifts. These supports have a unique roller system that allows the rolling hydraulic jack to glide easily under the entire length of the vehicle. The large heavy steel wheels allow the rolling jack to be positioned under the correct lifting points in a matter of seconds.

The Atlas RJ-6000 (Manual) comes standard with a set of peg style truck adapters which increases the lifting height of the lift pads. These truck adapters will allow the Atlas RJ-6000 rolling hydraulic jack to raise most pick up and larger trucks that will sit higher than the average passenger car.

The Atlas RJ-6000 can be equipped with an optional Atlas Air/Hydraulic Pump. The air/hydraulic pump would require a supply of compressed air (air compressor) to work properly.

The Atlas RJ-6000 rolling hydraulic jack features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas RJ-6000 are engaged, the hydraulic pressure from the lifting cylinder of the jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack). 
Atlas 412 Specifications  
Capacity 12,000 LB.
Lifting Height 74" (6' 2")
Overall Width of Columns (Without Motor) 126" (10' 6")
Overall Width of Columns (With Motor) 135" (11' 3")
Overall Length with Approach Ramps 230" (19' 2")
Overall Length without Approach Ramps 200" (16' 8")
Length Between Columns 184 1/4" (15' 4 1/4")
Runway Length 186 1/2" (15' 6 1/2")
Runway Width 22" (1' 10")
Thickness of Runway 5 1/2"
Width Between Runways 44 1/2" (3' 8 1/2")
Width Between Runway Rails 42" (3' 6")
Outside Runway to Outside Runway 84 3/4" (7' 3/4")
Clearance Under Runways 68 1/2" (5' 8 1/2")
Column Dimension 7" x 5"
Base of Column 10 1/8" x 9"
Clearance Between columns 112 1/4" (9' 4 1/4")
Height of Columns 82" (6' 10")
Maximum Wheel Base 175" (14' 7")
Drive Thru 98 1/2" (8' 2 1/2")
Column Thickness of Steel 3.5mm
Platform Thickness of Steel 5mm
Cross Beam Thickness of Steel 6mm
Cable Diameter 1/2"
Motor 4 HP, 220 Volt, Single phase
Oil Requirement 3-5 Gallons AW32/AW46
Shipping Weight 2,400 LBS.
Atlas RJ-6000 Jacks
Maximum Width 55 ¾"
Minimum Width 35"
Distance Between Runway Capability 32"-52"
First Locking Position 7"
Second Locking Position 10 1/2"
Maximum Lifting Height (With Adapters) 20 1/4"
Adapters 3" and 1 ½"
Maximum Capacity 6,000 LB.
Shipping Weight 350 lbs.

Atlas 412 12,000 LB. 4 Post Lift


 Warranty Information

5 Year Structural Warranty, 2 Year
Hydraulic Cylinder Warranty, and
1 Year Power Unit Warranty

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...



Business Info


Payments Accepted

Copyright 2019 MyToolEquipmentGuy Tel. 203-813-0414 (Direct) or Toll Free 877-572-8298. All Rights Reserved.
Sitemap | Bigcommerce Premium Themes by PSDCenter

Click the button below to add the Atlas 412 Combo 12,000 LB. Cap. 4-Post Lift & 2 x Atlas RJ-6000 Rolling Jacks (Manually Operated) to your wish list.