Loading... Please wait...

Categories

BendPak HD-9 Standard Width 4-Post 9,000 LB

Hover over image to zoom

  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5
  • Image 6
  • Image 7
  • Image 8
  • Image 9
BendPak
RRP: $3,460.00
$2,895.00 (You save $565.00)
SKU:
5175861
Weight:
1,872.00 LBS
Shipping:
Free Shipping

 Product Description

 

bendpak-authorized-dealer.gif
BendPak 9,000 LB  4-Post Lift HD-9 Standard Width
The HD-9 is your rugged, 9,000-lb. lifting solution. Perfect for vehicle storage and service—at the shop or in the garage. Whether you’re a service professional or a DIY’er, BendPak’s got the right lift for you. This model is available with optional casters, dip-trays, jack platform and more.

Free Shipping Continental US
Direct shipping points only. Surcharge may apply to rural & interline points

 

 

rj45-2-87441.1409993791.1280.1280.jpg

 

    Click here for Optional Rolling Bridge Jacks

 

 

*9,000-pound lifting capacity 
*117" Wide
*Overall Lenght 200"
*Height of Colums 88"
*Lenght of Run Ways 164"
*Max Rise 70"
*Lifting Time 45 sec.
*Motor 220 VAC/1 Ph

pdf.instructions.jpg  pdf.catalog.jpg   

  •  

     

    Description

     

    The space-saving design of the 9,000-lb. capacity HD-9 is ideal for vehicle storage in residential garages or commercial buildings. It also doubles as a great service lift for smaller shops who still want to do a big business..

    No special foundation is required and the installation is a cinch. Optional casters enable you to roll the lift outside or wherever best suits your needs. 

    The HD-9SWX is the high rise version of this lift. If you are looking to go wide, but keep it standard height, consider the HD-9SW.


    The HD-9 car lift is about the size of a typical parking space and will truly maximize your valuable floor area. Use the HD-9 for storing ATVs, snowmobiles, jet skis, golf carts, boats or just about anything else that needs to be off the ground. Now you can finally make use of that wasted vertical space above your car. If you’ve got at least standard 8-foot ceiling, this lift will work for you.

     

     The HD-9SWX is the high rise version of this lift. If you are looking to go wide, but keep it standard height, consider the HD-9SW.

    The HD-9 car lift is about the size of a typical parking space and will truly maximize your valuable floor area. Use the HD-9 for storing ATVs, snowmobiles, jet skis, golf carts, boats or just about anything else that needs to be off the ground. Now you can finally make use of that wasted vertical space above your car. If you’ve got at least standard 8-foot ceiling, this lift will work for you.

     

    The HD-9 is the standard version of this lift. If you are looking for a narrow-width model, consider the HD-9ST.

    Dependable design
    4 heavy-duty, high-quality, stainless steel lifting cables and a single hydraulic cylinder mounted underneath the runway makes this lift the most durable, maintenance-free lifting system on the market.

    Dual-hub cable sheaves
    Reduce stress and fatigue on the axles, sheaves and cables. We insist on using dual-hub cable sheaves, even if they cost us more to make. When you buy BendPak, we throw in peace of mind as a free gift.

    Multi-level locking positions
    The HD-9 is equipped with multiple adjustable height locking positions for variable-height parking. A convenient push-button pneumatic safety lock control releases all four independent safety locks simultaneously.

    Heavy-duty aircraft cable
    Each lift is supplied with 4 high-quality stainless steel lifting cables, rated at 14,400 lbs. each. The combined rating of these cables is 640% of the maximum lifting capacity of the entire lift! And we make sure it looks tidy too—all lifting cables are fully enclosed within the lift structure itself.

    Electric / hydraulic power system
    We incorporate maintenance-free electric hydraulic power systems into each lift for ultimate dependability, and all controls are conveniently located within close reach.

    Large base plates
    10" x 12" base plates provide a solid foundation for the HD-9.

    Single hydraulic cylinder
     Leak proof cylinder technology only available for BendPak four-post lifts

    Each lift is equipped with a single hydraulic cylinder, hidden away under the runway for minimum exposure and maximum reliable performance. Our industrial-grade hydraulic cylinders feature a single-piece, pilot fitted, machined steel piston, wrapped with specially designed, pressure loaded U-cup piston seals, backups and wear bands to virtually eliminate fluid bypass. The micro-smooth chrome-rod is machined from high-yield, ground and polished C-1045/50 micro-alloy steel and plated to a minimum of .001" diametrically, to ensure superior cylinder operation and life. The superior-design high durometer, mechanically-loaded rod seals make rod leakage is a thing of the past while a specially formulated abrasion-resistant urethane rod wiper provides exclusion protection. The welded cylinder body is made from robust steel tubing produced to exceed ASTM specifications. This combination of superb base material and superior processing ensures that the cylinders remain straight, smooth and last a very long time. An integrated flow restrictor provides a controlled descent in the case of an unexpected hose rupture.

    Durable powder-coat finish
    All HD-Series lifts feature a durable powder-coat finish that gives the metal a high-quality, extremely durable finish which can withstand even the harshest environmental or chemical conditions. Unlike other companies that claim to powder coat, we take pride in our meticulous 10-step process. First, all parts are visually inspected before being sandblasted. Afterwards, the parts are washed in our 5-stage phosphate tanks that can accommodate parts up to 25' long. Once cleaned, they're immediately dried to avoid rust production, and then outgassed. Outgassing pre-bakes the parts in a curing oven, reducing the possibility of blemishes that may be hiding in the pores of the metal. If not properly outgassed, imperfections in the metal may bubble during the curing process and most likely will cause chips in the powder. After the parts are washed and outgassed, any surfaces and / or threaded holes that need to be masked or plugged, are done so with high-temperature masking tape and silicone plugs. Next, the parts are given a quick thinner wipe to remove any light debris or fingerprints, before being hung on an electrostatically grounded conveyor line. The powder is finally applied using an electrostatic spray gun. The powder "sticks" to the surface in a fashion similar to how dust sticks to a television screen. Once the parts are powder coated, the carts are rolled into our curing oven and baked at 400° F for 45 minutes.

    Caster kit
    Optional 4-piece caster kit makes your lift portable.
    (recommended to use without vehicle on lift)

    Four models to choose from

    Take your pick. You're currently looking at the standard-width, standard-rise HD-9. The HD-9ST is the narrow model, the HD-9STX is the tall and narrow model and the HD-9XW is the standard-width, tall model.

    Integrated design
    Lifting cables, airlines, safety latches and sheaves are all fully enclosed.

    Longer approach ramps
    These approach ramps were designed a little longer to help when loading low ground clearance vehicles. It's the little bit that makes a big difference.

    Automatic safety locks
    Aircraft-quality stainless steel and aluminum pneumatic cylinders release all 4 locks simultaneously with the simple push of a button. The spring-loaded safety locks automatically engage continuously as the lift is raised. For added safety, a secondary lock system acts as a slack-cable device to engage in the unlikely event of cable failure.

    *Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult www.autolift.org for a complete list or contact BendPak viacontact@bendpak.com.

     

    Features & Specifications
      • 9,000-lb. maximum lifting capacity
      • Freestanding design
      • Perfect for parking, storage and service
      • Runways accommodate narrow and standard vehicles
      • Runways include rail-kit for optional accessories
      • Electric / hydraulic power system
      • Single hydraulic cylinder mounted underneath runway
      • Fully enclosed lifting cables, safety locks and sheaves
      • Internal anti-sway slider blocks in each column
      • Oversized self-lubricating cable rollers
      • Features heavy-duty 3/8" aircraft cable
      • Rugged 1-1/4" roller axles
      • Multi-position safety locks in each column
      • Adjustable lock ladders
      • Runways feature non-skid surface
      • Push-button pneumatic safety release
      • Independent backup slack-cable safety latches
      • Customizable power unit location
      • Removable approach ramps for additional drive-under clearance
      • Longer approach ramps for low-ground clearance vehicles
      • Optional drive-thru ramps available
      • Optional drip trays available
      • Optional solid deck available to increase storage capacity
      • Optional 4,500-lb. air / hydraulic rolling jacks available (Model RJ-45)
      • ETL Approved


    Best Warranty Car Lifts - BendPak

    Will your four-post car lift fit?

    Safe balancing for BendPak car lifts

    How to choose the right car lift for you


    BendPak's Top 10 Car Lift Buyers Guide


    • Lifting capacity*: 9,000 lbs. / 4,082 kg
      • *Max capacity / front axle: 4,500 lbs. / 2,041 kg
      • *Max capacity / rear axle: 4,500 lbs. / 2,041 kg
    • Overall width: 116-3/4" / 2,965 mm
    • Outside length: 174" / 4,420 mm
    • Overall length: 200" / 5,080 mm
    • Height of columns: 88" / 2,235 mm
    • Runway min height: 4-1/2" / 114 mm
    • Max rise: 70" / 1,778 mm
    • Max lifting height: 74-1/2" / 1,892 mm
    • Width between posts: 106-3/4" / 2,711 mm
    • Runway width: 19" / 483 mm
    • Width between runways: 37-1/2" - 44-3/8" / 952 - 1,127 mm
    • Length of runways: 164" / 4,166 mm
    • Min. wheelbase @ rated capacity: 115" / 2,921 mm
    • Min. wheelbase @ 75% capacity: 100" / 2,540 mm
    • Min. wheelbase @ 50% capacity: 85" / 2,159 mm
    • Min. wheelbase @ 25% capacity: 70" / 1,778 mm
    • Locking positions: 12
    • Lock spacing: every 4" / 102 mm
    • Lifting time: 45 sec
    • Motor: 220 VAC / 60 Hz / 1 Ph

    Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

    *Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult www.autolift.org for a complete list or contact BendPak viacontact@bendpak.com

     

 Product Videos

BENDPAK 4 POST LIFT HD-9 CASTER KIT REVIEW
  • BENDPAK 4 POST LIFT HD-9 CASTER KIT REVIEW
    To see more tool reviews, and participate in workshop discussi...
  • Lotus Elise on BendPak HD-9
    http://www.bendpak.com/car-lifts/four-post-lifts/HD-9.aspx The...
  • BendPak RJ-45 Rolling Bridge Jacks for HD-9 Four Post Lifts
    To see more tool reviews, and participate in workshop discussi...

 Warranty Information


Better Products – Better Service – Better Value
For more than a decade, America’s best lift has been coupled with the best warranty in the business. Instead of hiding behind a long veil of marketing fluff, we’re proud to deliver our warranty up front for all to see. To make sure we deliver our customers lifting products worthy of our 5-2-1 warranty, we developed our Design-Build-Quality-Deliver directive. This Zero-Tolerance for Defects initiative combined with our 5-2-1 Warranty is BendPak’s way of backing up what we claim. We employ a dedicated team of design engineers who are responsible for detecting and correcting any issue no matter how small before it gets to the customer. Five years is a long time, so we’ve got to get it right before we ship. The best warranty in the business gives you more than just peace of mind; it’s proof that we took a little extra care building your lift and every precaution was taken to maintain the highest degree of quality, dependability and reliability.

Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.

» Five Years (60-Months) Bumper-to-Bumper Warranty on the lift structure
» Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
» One Year (12-Months) Labor Warranty on site or at factory
» One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance

Click here for full details.

 Find Similar Products by Category

 Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

You Recently Viewed...

 

Categories

Business Info

newsletter

Payments Accepted

Copyright 2017 MyToolEquipmentGuy Tel. 203-813-0414 (Direct) or Toll Free 877-572-8298. All Rights Reserved.
Sitemap | Bigcommerce Premium Themes by PSDCenter

Click the button below to add the BendPak HD-9 Standard Width 4-Post 9,000 LB to your wish list.